1) heating[英]['hi:tɪŋ] [美]['hitɪŋ]
制热
1.
Development of Cooling,Heating,Water Heating Triple Mini-type Central Air Conditioner/central Water Heater System;
一种新型的制冷、制热、制热水联合机组的研发及其经济分析
2.
Design and heatingperformance of solar-assisted heat pump with truncated-cone-type evaporator
圆台型太阳能热泵设计及其制热性能
3.
The characteristics of heatingcapacity,power input,COP,compression ratio,discharge temperature,suction temperature,sub-cooled temperature and superheat temperature versus environment temperature were tested while the temperature changed form 7 ℃ to-10 ℃.
对以R410A为制冷剂的风冷热泵冷热水机组完成了变环境温度制热运行的实验。
2) hydrothermal synthesis
水热制备
1.
The formation mechanism of the nanocables was studied and the optical experimental conditions were found for the hydrothermal synthesisof uniform iron-phosphates/C nanocables.
以抗坏血酸、氯化亚铁和次亚磷酸钠为原料, 采用一步水热法制备了以磷酸铁为芯、含碳化合物为壳的磷酸铁/碳纳米电缆,通过 XRD、FTIR、SEM 和 TEM 等手段对产物的成分和结构进行了表征,对选定条件下磷酸铁/碳纳米电缆的生长机理进行了探讨,获得了水热制备磷酸铁/碳纳米电缆的最佳实验条件。
3) TMCP
热机轧制
1.
Effect of
TMCPon Structure and Performance of Middle Carbon Cold Heading Steel;
热机轧制对中碳冷镦钢组织和性能的影响
2.
,grain refinement can be achieved by thermal mechanical controlled rolling(TMCP) in metastable austenite region and new grain growth is restrained by using the practice of holding the transfer bar and rolling at low finish rolling temperature to allow γ/α phase transformation in non-recrystallization region.
沙钢集团于2006年建成现代化宽厚板生产线,采用当今世界上诸多先进的工艺装备和工艺技术,亚稳态奥氏体区热机轧制实现晶粒细化,靠中间坯待温时间及未再结晶区γ/α相变较低终轧温度抑制新晶粒成长。
4) control of heat source
控制热源
5) heat-die compaction
热模压制
1.
This paper outlined its technical characteristics and new developments of warm compaction,for example,warm flow compaction,heat-die compactionetc.
本文概述了温压工艺的特点及其最新的发展,如流动温压、热模压制等,重点讨论了热模压制工艺的技术特点与应用,并指出以AncorMax D为代表的热模压制工艺由于工序比常规温压工艺更简单,压制温度更低,因此在将来很有可能取代常规温压工艺,成为高密度粉末冶金零件的一种非常有应用前景的方法。
6) thermal regulation
热工制度
1.
This paper introduces the factors affecting stability of thermal regulationof mechanized shaft Kiln,and puts forward measures how to stabilize thermal regulationof mechanized shaft Kiln.
介绍了影响机立窑热工制度稳定的因素,给出了稳定热工制度的措施。
2.
The results present that the thermal regulationof heat furnace with hot charge should be alternated according to the theory of heat furnace.
结果表明,热装加热炉的热工制度如不作调整,物料热装带来的节能潜力得不到充分发挥,调整后的加热炉温度制度将具有最大的节能潜力。
补充资料：风力制热
风力制热
wind power heating
风力制热(wind power heating)将风轮旋转轴输出的机械能通过风能制热装置直接或间接转换成热能或电能。风力制热系统对风的质量要求不高，制热装置结构简单，容易满足与风力机最佳匹配的要求，并能在很宽的风速范围内正常工作，多应用于禽舍、温室和水产养殖的加温，农产品干燥以及建筑采暖等方面。风能制热装置按制热方式不同可分为两大类。①采用直接制热方式:有固体与固体摩擦制热装置，搅拌液体制热装置，油压阻尼式制热装置，压缩气体制热装置。②采用间接制热方式:有风能转换电能后用电阻制热、涡电流制热、电解水制氢取热等装置。风能直接制热装置的效率要比间接制热装置的效率高，制热系统也简单。风力制热的综合效率比风力发电和风力提水的综合效率高。一般风力发电综合效率低于35%，而风力制热的综合效率在40%以上。 (龙泽舜)
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条
专业词汇(按中图法分类)